Load data for .260 PICRA + .264 | 159gr | RWS TMR

Recommended Powder(s): none

Load Specifications

(Use the Personalized Load Calculator below to adjust )

Bullet:	.264 \| 159gr \| RWS TMR
Manufacturer SKU:	2145685
Bullet Weight:	159gr \| 10.3g
Bullet Diameter:	0.264" \| 6.71mm
Bullet Length:	1.180" \| 30.0mm
Caliber:	.260 PICRA load data
Case Length (l3):	1.515" \| 38.5mm
Cartridge Length (C.O.L.):	2.404" \| 61.1mm
Seated Depth:	0.291" \| 7.4mm
Shank Seated Depth:	0.291" \| 7.4mm
Case Capacity:	38.6 Grains of Water \| 2.51 cm³
Primer Size:	Large Pistol (LP)
Max. allowed Pressure:	56565 psi \| 3900 bar
LID:	LID_B5382_C251
Last updated:	2025-01-01

Load data for 42 loads in caliber .260 PICRA with .264 | 159gr | RWS TMR bullet and 21 powders such as none. The key underlying parameters are shown in the table above.

Important Notice: DO NOT go below Minimum Charge or above Maximum Charge unless there are reasons. Since xxlreloading.com has no control over the equipment and components used by the customer and the data used in connection with the website, any responsibility and liability for the results achieved is rejected. Also see our Terms of Service.

Questions regarding the load data: Please read the information in the next tab "Explanations".
A load must fulfill certain criteria to be listed in the default view below - see "powder criteria to fulfill to be listed".

Our load data might deviate from other sources - see the "most common reasons for deviations".

All loads are based on the bullet and case dimensions shown under "Load Specifications" - see "reloading suggestions" if you deviate.

You can set your specifications in the "Personalized Load Calculator".

Go to the bottom of the "Dashboard " page to set the measure system (imperial vs. metric)
No data yet
C.O.L. (Inch)
C.O.L. (mm)
We recommend you limit powder range to relevant brands to speed up re-calculation of results
Use the Personalized Load Calculator to customize loads to your own specific requirements. Find more details in the help section.

Our default view only displays powders/loads that fulfill certain criteria: Max pressure of a load <=90% of Max. Standardized Pressure. Fill Rate (Min FR): >80% and <100% for rife loads, >60% and <100% for pistol loads. Min. Propellant Combustion (Min z): >90% for rifle loads , >80% for pistol/revolver loads. Relax these criteria at your own risk to potentially get more powders shown in the load tables.
Case Length (Inch)
Case Length (mm)
CaseCapacity (GoW)
Min z (%)
Min FR (%)
Max FR*
Barrel Length (Inch)
Barrel Length (cm)
Safety Buffer (%)
.

Click on the desired row in the tables below to add a specific load / powder to your Diary and manage there.

Powder	Charge	FR	MaxP	%	V(0)	z
ADI AP 100	<<locked>>	65%	50705	90%	**96	100%
ADI APS 350	<<locked>>	73%	50183	89%	**58	100%
ADI APS 450	<<locked>>	72%	50256	89%	**65	100%
ADI AS 30	<<locked>>	68%	50894	90%	**84	100%
Accurate No. 11 FS	<<locked>>	64%	50328	89%	**21	100%
Accurate Solo 1000	<<locked>>	65%	50140	89%	**81	100%
Accurate Solo 1250	<<locked>>	62%	50531	89%	**07	100%
Baschieri & Pellagri 100	<<locked>>	62%	50401	89%	**81	100%
Hodgdon Clays	<<locked>>	71%	49864	88%	**58	100%
Hodgdon TrailBoss	<<locked>>	95%	32750	58%	**8	100%
Maxam CSB 1	<<locked>>	65%	49980	88%	**94	100%
Maxam CSB 3	<<locked>>	63%	49487	87%	**84	100%
Maxam CSB 4	<<locked>>	63%	49327	87%	**81	100%
Maxam CSB 5	<<locked>>	64%	50343	89%	**71	100%
ReloadSwiss RS 14	<<locked>>	94%	32967	58%	**1	100%
ReloadSwiss RS 30	<<locked>>	71%	50082	89%	**21	100%
SNPE Vectan BA10	<<locked>>	67%	49327	87%	**61	100%
SNPE Vectan BA6 1/2	<<locked>>	76%	50894	90%	**75	100%
Somchem S265	<<locked>>	70%	50850	90%	**07	100%
Vihtavuori N110	<<locked>>	67%	49313	87%	**85	100%
Vihtavuori N32C Tin Star	<<locked>>	86%	50763	90%	**55	100%

Max Load - Barrel Length: 5.50''

Powder	Charge	FR	MaxP	%	V(0)	z
ADI AP 100	<<locked>>	61%	45513	80%	**47	100%
ADI APS 350	<<locked>>	61%	39697	70%	**50	100%
ADI APS 450	<<locked>>	61%	40292	71%	**66	100%
ADI AS 30	<<locked>>	61%	43584	77%	**06	100%
Accurate No. 11 FS	<<locked>>	61%	45542	81%	**62	99%
Accurate Solo 1000	<<locked>>	61%	46543	82%	**45	100%
Accurate Solo 1250	<<locked>>	61%	48530	86%	**88	100%
Baschieri & Pellagri 100	<<locked>>	61%	48501	86%	**58	100%
Hodgdon Clays	<<locked>>	61%	40973	72%	**66	100%
Hodgdon TrailBoss	<<locked>>	60%	18333	32%	**5	100%
Maxam CSB 1	<<locked>>	61%	46383	82%	**65	100%
Maxam CSB 3	<<locked>>	61%	47718	84%	**65	100%
Maxam CSB 4	<<locked>>	61%	47514	84%	**61	100%
Maxam CSB 5	<<locked>>	61%	46688	83%	**35	100%
ReloadSwiss RS 14	<<locked>>	61%	18594	33%	**4	100%
ReloadSwiss RS 30	<<locked>>	61%	36869	65%	**50	100%
SNPE Vectan BA10	<<locked>>	61%	44251	78%	**06	100%
SNPE Vectan BA6 1/2	<<locked>>	61%	33112	59%	**61	100%
Somchem S265	<<locked>>	61%	39479	70%	**83	99%
Vihtavuori N110	<<locked>>	61%	41321	73%	**83	100%
Vihtavuori N32C Tin Star	<<locked>>	61%	31705	56%	**5	100%

Start Load - Barrel Length: 5.50''

Any powder missing? Then click here.

FR ... fill rate of the cartridge in percent

MaxP ... max. pressure of load in psi or bar

% ... max. pressure of load in percent of the maximum allowed pressure for this caliber

V(0) ... muzzle velocity in feet per second (fps) or meters per second (m/s)

z ... powder burnt in percent

[...] *... not dangerous but load has suboptimal powder burnt with possible characteristics such as extensive muzzle flash or inaccurate loads.

[...] ²... fill rate low - you might want to consider using a filler to ensure proper ignition.

[...] ᴾ... possible press load - work up slowly to this load while watching for signs of excessive pressure.

👍 ... recommended powder/load for this caliber and bullet combination based on its ballistic performance.

<<locked>>... you need to buy an access license to unlock the data